Request a Quote
Home » Thrust Bearings » T-100 Series

T-100 Banded Thrust Ball Bearing Series

Auburn Enclosed Style T-100 Thrust Ball Bearing with Outside Band

The T-100 Banded Thrust Ball Bearing Series is recommended for use in exposed locations where protection from dust, dirt, water, or other foreign matter is required. The balls are retained between two hardened steel races banded together by a mild steel or brass sleeve on the outside diameter.

The “V” grooved raceways on this bearing enable it to carry radial loads equal to 25% of its thrust load capacity, while decreasing the amount of friction created by a full contact round groove design.

The banded style of the T-100 series typically allows more balls per bearing, thus providing greater thrust capacity than a 3 piece retained style bearing of similar dimensions.

The T-100 Banded Thrust Ball Bearing is available in inch dimensions from 0.313″ through 6.5″ bore, 0.688″ through 8.75″ OD, and 0.313″ through 1.5″ height.

Please note: the following dimensions are shown in inches.
Bearing NumberBore (A)OD (B)Height (H)Stock?
T-100-000.3130.6880.313YesDetails
T-100-00.3750.7500.313YesDetails
T-100-3/80.3751.1880.500YesDetails
T-100-1/20.5001.1880.375YesDetails
T-100-10.5001.1880.625YesDetails
T-100-20.6251.3750.625YesDetails
T-100-3Details
T-100-4Details
T-100-5Details
T-100-6Details
T-100-7Details
T-100-8Details
T-100-9Details
T-100-101.0632.1880.813NoDetails
T-100-111.1252.1880.938YesDetails
T-100-121.1882.1880.688YesDetails
T-100-131.2502.1880.688YesDetails
T-100-14Details
T-100-15Details
T-100-16Details
T-100-17NoDetails
T-100-17AYesDetails
T-100-18NoDetails
T-100-19NoDetails
T-100-19ANoDetails
T-100-20NoDetails
T-100-21YesDetails
T-100-22YesDetails
T-100-23YesDetails
T-100-24YesDetails
T-100-25YesDetails
T-100-26NoDetails
T-100-27YesDetails
T-100-28NoDetails
T-100-29NoDetails
T-100-30YesDetails
T-100-31YesDetails
T-100-32NoDetails
T-100-33YesDetails
T-100-34NoDetails
T-100-35NoDetails
T-100-36NoDetails
T-100-37NoDetails
T-100-38YesDetails
T-100-39NoDetails
T-100-40NoDetails
T-100-41YesDetails
T-100-41ANoDetails
T-100-42YesDetails
T-100-43NoDetails
T-100-43ANoDetails
T-100-44NoDetails
T-100-45NoDetails
T-100-46NoDetails
T-100-47YesDetails
T-100-48NoDetails
T-100-49NoDetails
T-100-50NoDetails
T-100-51NoDetails
T-100-52NoDetails
T-100-53YesDetails
T-100-54YesDetails
T-100-56NoDetails
Other Info & Resources

Mounting Instructions: Enclosed Style T-100 Ball Thrust Bearing is generally installed so that the race A is centered by the shaft and rotates with it. The race with the sleeve attached to it and having a clearance bore A’ is seated against a fixed part of the machine and is stationary. If installed in a recess, a clearance of one-eight inch or more should be left around the outside diameter B so that the shaft should wear in its journal bearings; the thrust bearing will be free to follow without cramping or wedging the balls.

Downloads:
T-100 Series Datsheet
T-100 Series Catalog Page

 

Related Articles:
Auburn “V” Groove Reduces Friction & Drag in Thrust Bearings